Search

Huntron Tracker 3200S

Trusted Technology in Power-off Testing for your Circuit Board Repair needs

Quick Enquiry

If you want to know more about Huntron Tracker 3200S

The NEW Huntron Tracker 3200S is designed to encompass our product history and leadership in power-off test by providing powerful test and troubleshooting solutions. The Tracker 3200S features variable range parameters resulting in hundreds of voltage, source resistance and frequency combinations. You can create Tracker ranges to precisely fit your needs.

The Tracker 3200S uses a color, touch screen LCD for control of features such as range configuration, front panel pin selection and Channel A/B settings. The Tracker 3200S LCD provides a very fast screen refresh rate for quick screening of component pins and display the A and B channel signatures at the same time (A+B mode). The built-in Pulse Generator enables you to dynamically test gated devices such as SCRs, TRIACs and relays. It features two 64 pin IDC connectors for use with IC clips or custom cable interfaces or connect to a Huntron Access Prober for full diagnostic automation.

Huntron Workstation Software
The Huntron Workstation software is included enabling you to automate analog signature analysis (ASA) based tests by creating a test plan, capturing signatures, comparing to stored signatures and viewing the results. The ability to automatically store signatures and document a specific test procedure allows for the sharing of knowledge among all users.

Save Your Favorite Range Combinations
Most Tracker users have their preferred range settings and the Tracker 3200S can save four range combinations that you use the most. These can be selected on the touch screen display (buttons 1-4).
The LCD also displays current ranges settings, pulse generator settings, current selected pin, SigAssist calculated values (resistance, capacitance, power, forward and reverse diode breakdown voltages), A vs. B comparison tolerance and Pass/Fail indication.

  • Add the benefits of Power-Off test to your current diagnostic test strategy
  • Can be used as a Stand-alone unit using the convenient front panel controls and touch screen LCD
  • Match the circuit impedance by setting the applied voltage, frequency and source resistance
  • Built-in Pulse Generator for testing gated devices such as relays, SCRs and TRIACs
  • 128 pin scanning with 128 Commons using the built-in front panel IDC ribbon cable connectors
  • Display A or B channels individually, in the switching ALT mode or in A+B mode to display both signatures at the same time
  • Connect to a Huntron Access Prober for full test automation
  • Use the Huntron Workstation software to create circuit board tests, store analog (V-I) signatures, make good vs. bad comparisons and present the results
  • Having the Good board signatures stored on your PC eliminates the need to keep one for direct comparison
  • A software based test allows for the sharing of board test knowledge with all personnel
Number of Voltages plus values 24 voltages: 200mV, 400mV, 600mV, 800mV, 1V to 20V in 1V steps including 10V (Low), 15V (Med 1), 20V (Med 2)
Number of Resistances plus values 16 resistances: 10Ω, 20Ω, 50Ω, 100Ω, 200Ω, 500Ω, 1kΩ, 2kΩ, 5kΩ, 10kΩ, 20kΩ, 50kΩ, 100kΩ, 54Ω (Low)*, 1.2kΩ (Med 1)*, 26.7kΩ (Med 2)*
* Through Huntron Workstation only
Number of Frequencies plus values 40 frequencies: 20Hz to 190Hz in 10Hz steps; 200Hz to 1.9kHz in 100Hz steps; 2kHz to 5kHz in 1kHz steps
Range Selection Stand alone mode: Front panel push buttons and preset LCD buttons
Remote Mode: Controlled by Huntron Workstation
Display Color TFT LCD with Touch screen; LED back light
Pulse Generator Level: 0 to +/- 10V DC or Square wave; Pulse mode width: 2% to 50% duty cycle; Source Resistance: 100Ω; Maximum current: 100mA per channel
Front Panel Connections Banana jacks for A/B Test channels and Common
Banana jacks for Pulse Generator outputs (G1, G2)
Rear Panel Connections BNC connectors for A/B Test channels and Common (used to interface to Access Prober); AUX connector for Footswitch accessory (included)

Tracker Model 30 Datasheet