Impedance stabilization networks (ISN, or with CISPR 16-1-2 called AAN: asymmetric artificial network) are defined for measuring of conducted common mode disturbances at information technology equipment (ITE) as required in CISPR 22 and CISPR 32. The ISN is placed between the equipment under test (EUT) and auxiliary equipment (AE) or load which are necessary for the operation of the EUT. The ISN establishes the common-mode termination impedance for the EUT’s telecommunications port during measurement and emulates the unsymmetrical contribution (longitudinal conversion loss, LCL) of the connected line. Different ISNs are available in relation to the line category, line numbers and pin-arrangement.
The ISN T8 is designed for measurements on up to four unscreened single balanced pairs and consists of one basic network (ISN T800) with D sub 25 connectors and special adapter sets. A set of adapters consists of two pieces of LCL adapters to arrange the lines and realize longitudinal conversion loss (LCL)- requirements for the EUT-side in relation to the use cable category (cat. 3, cat. 5) and one piece of connection adapter arranges the lines for the AE-side. Teseq offers two different adapter sets – ADS T800 and ADS T8x0. ADS T800 gives the connection to RJ45 sockets with pin-arrangements of EIA/TIA T568A respectively T568B. The adapter set ADS T8x0 offers changeable pin-arrangements via 1 mm banana connectors for each pin combination of RJ11/RJ45.
Parameter
Value
Frequency range
150 kHz to 30 MHz
Line parameters
1 up to 4 pair(s)
Power rating (EUT- and AE Port)
AC max. voltage (line to ground): 63 V
DC max. voltage (line to ground): 100 V
Current max.: 600 mA (line), 1200 mA (pair)
Test voltage: 200 VDC, 2 sec
Common mode impedance (EUT Port) 150 kHz to 30 MHz
150 Ω ±20 Ω
Phase angle (EUT Port) 150 kHz to 30 MHz
0° ±20°
CISPR 15
CISPR 16-1-2
CISPR 16-2-1
CISPR 22
CISPR 32
EN 61000-6-3
EN 61000-6-4
ISN T8 Datasheet
CAS ISN
Calibration Kit for ISN T
Meets CISPR 22 ed. 5.2 and CISPR 16-1-2
Optional extensible for measurements on ISN T2 and ISN T8-Cat6
Measurements for common mode impedance, phase angle, voltage division factor, decoupling attenuation (isolation) and longitudinal conversion loss (LCL)
The calibration kit CAS ISN is made for function tests and remeasurements on impedance stabilization network (ISN) for unshielded balanced pairs. Measuring parameters are common mode (CM) impedance, phase angle, voltage division factor, decoupling attenuation (isolation) and longitudinal conversion loss (LCL). Impedance stabilization networks (ISN) are defined in CISPR 22 and CISPR 16-1-2. The CISPR 16-1-2 gives additional requirements and provides examples and measurements for the networks. The ITU-T recommendations G.117 and O.9 offers the background knowledge for measurements on symmetrical telecommunication lines.
Parameter
Value
Frequency range
100 kHz to 100 MHz
Impedance for the network analyzer ports
50 Ω
Connector
BNC-type female
Impedance for the balanced port
100 Ω
Connectors for the balanced ports and ground
1 mm banana
CAS ISN Datasheet
FIX ISN
Magnetic fixture for ISN T2A, ISN T4A, ISN T8, ISN T8-Cat6 or CDN T8
Improvement of the ISN earth connection to steel surfaces
Allows vertical positioning of the ISN (chamber wall)
Easy positioning of the ISN in the setup
Ruggedly designed
The magnetic fixture for ISNs (Impedance Stabilization Network) improves the earth connection to steel surfaces as typical used for Faraday cages. Its design provides a constant and stable pressure of the ISN enclosure against the ground plane. The standard CISPR 22/EN 55022 allows to place the ISNs also to a vertical ground plane which can be done easily with the use of FIX ISN.
This website uses cookies to ensure you get the best experience on our website. AcceptRead More
Privacy & Cookies Policy
Privacy Overview
This website uses cookies to improve your experience while you navigate through the website. Out of these cookies, the cookies that are categorized as necessary are stored on your browser as they are essential for the working of basic functionalities of the website. We also use third-party cookies that help us analyze and understand how you use this website. These cookies will be stored in your browser only with your consent. You also have the option to opt-out of these cookies. But opting out of some of these cookies may have an effect on your browsing experience.
Necessary cookies are absolutely essential for the website to function properly. This category only includes cookies that ensures basic functionalities and security features of the website. These cookies do not store any personal information.
Any cookies that may not be particularly necessary for the website to function and is used specifically to collect user personal data via analytics, ads, other embedded contents are termed as non-necessary cookies. It is mandatory to procure user consent prior to running these cookies on your website.