Search

EM Test VCS 500N12 Series

12kV Combination Wave Simulator

  • Surge pulses up to 12kV/6kA
  • Single phase or three-phase coupler up to 100A (external option)
  • Fail inputs
  • Warning lamp control
  • Emergency interlock
  • Standard Test routines
  • USB (optical link) and GPIB interface

Quick Enquiry

If you want to know more about EM Test VCS 500N12 Series

Combination Wave Simualtor

Surge pulses occur due to direct or indirect lightning strokes to an external (outdoor) circuit. This leads to currents or electromagnetic fields causing high voltage or current transients. Another source for surge pulses are switching transients originating from switching disturbances and systems faults.
Due to the characteristic of the phenomenon nearly every electrical and electronical device may suffer from such lightning events which justifies the necessity of surge tests being widely performed. Surge voltage can reach several thousands of volts and surge current is seen to reach several thousands of amps.
  • EN 61000-4-5
  • EN 61000-4-9
  • IEC 60255-22-5
  • IEC 61000-4-5
  • IEC 61000-4-9
  • IEC 61326
  • IEC 61850-3
  • ITU-T K.12
  • ITU-T K.20
  • ITU-T K.45

VCS 500N12 – Combination wave simulator for 12kV/6kA

The VCS 500N12 combination wave simulator generates surge voltages up to 12kV and surge currents up to 6kA as it is required for component testing (e.g. overvoltage protection for telecommunication devices). To apply the surge pulses to power supply lines an external coupling/decoupling network either single phase or three-phase can be connected. The coupling modes and the source impedance are set automatically controlled by the VCS 500N12.
Fail inputs are offered as standard for DUT monitoring purposes. Peak values of voltage and current are shown in the display and these values are transferred to the software for reporting.
To comply with safety regulations the VCS 500N12 is equipped with a contact to control warning lamps and with a safety interlock.
Pre-programmed Standard Test routines allow highest user convenience. Still the VCS 500N12 offers the Quick Start test routine where parameters can be changed on-line during the test to evaluate the susceptibility level of an individual DUT.

iec.control Software for control and documentation

Outstanding user convenience, clearly structured windows and operation features, EM TEST’s comprehensive standards library along with the flexibility to easily generate user specific test sequences are the main features of iec.control software. The software will be automatically configured in accordance with the connected EM TEST generators. Extensive reporting capabilities help the user to create test reports that meet international requirements.
The iec.control is supported by Windows 7, Windows 8 and Windows 10. Remote control is achieved either via Ethernet or optical interface with USB connector at the PC side.
The iec.control supports various interfaces for the communication to external measuring devices.

CNV 504/508 N-series – Surge coupling/decoupling networks for signal/data lines  

CNV 504/508 N- and T-series coupling/decoupling networks are available to perform surge tests on I/O lines, signal/data lines and telecom lines as per IEC/EN 61000-4-5 Ed 3.0

CNV 503 Series – 3phase coupling/decoupling networks for surge

EM TEST offers a range of fully automatic 3phase coupling/decoupling networks for surge to extend the test capability for three-phase DUTs. The networks have a rated current of up to 100A.

CNI 503 Series – 3phase coupling/decoupling networks for burst and surge

EM TEST offers a range of fully automatic 3phase coupling/decoupling networks for burst and surge to extend the test capability for three-phase DUTs. The networks have a rated current of up to 100A

MS 100N – magnetic field coil for power-frequency and pulsed magnetic fields

The MS 100N is a 1m x 1m magnetic field coil as specified in IEC/EN 61000-4-8 and IEC/EN 61000-4-9. Its design allows easy moving of the coil. The field coil is adjustable in height and allows for 360degree rotation.
To generate power-frequency magnetic fields in the lower range the current transformer MFT 30 is used while high-field strength above 100 A/m up to 1000 A/m requires the MFT 100 current transformer.

 

VCS 500N12 Series Datasheet 

Related products

Contact

Linkedin Youtube Twitter

Accelonix Services

Servicemenu

Newsletter

Subscribe to our Accelonix newletter and be informed about our newest products and our workshops.

Subscribe Newsletter
Copyright © 2024 Accelonix